Backup XML format
Backup XML ¶
Creating a backup, whether full or incremental, is done
via virDomainBackupBegin()
, which takes an XML
description of the actions to perform, as well as an optional
second XML document describing a
checkpoint to create at the same point in time. See
also a comparison between
the various state capture APIs.
There are two general modes for backups: a push mode (where the hypervisor writes out the data to the destination file, which may be local or remote), and a pull mode (where the hypervisor creates an NBD server that a third-party client can then read as needed, and which requires the use of temporary storage, typically local, until the backup is complete).
The instructions for beginning a backup job are provided as
attributes and elements of the
top-level domainbackup
element. This element
includes an optional attribute mode
which can be
either "push" or "pull" (default
push). virDomainBackupGetXMLDesc()
can be used to
see the actual values selected for elements omitted during
creation (for example, learning which port the NBD server is
using in the pull model or what file names libvirt generated
when none were supplied). The following child elements and attributes
are supported:
-
incremental
- An optional element giving the name of an existing checkpoint of the domain, which will be used to make this backup an incremental one. In the push model, only changes since the named checkpoint are written to the destination. In the pull model, the NBD server uses the NBD_OPT_SET_META_CONTEXT extension to advertise to the client which portions of the export contain changes since the named checkpoint. If omitted, a full backup is performed.
-
server
- Present only for a pull mode backup. Contains the same
attributes as
the
protocol
element of a disk attached via NBD in the domain (such as transport, socket, name, port, or tls), necessary to set up an NBD server that exposes the content of each disk at the time the backup is started. -
disks
- An optional listing of instructions for disks participating
in the backup (if omitted, all disks participate and libvirt
attempts to generate filenames by appending the current
timestamp as a suffix). If the entire element was omitted on
input, then all disks participate in the backup, otherwise,
only the disks explicitly listed which do not also
use
backup='no'
will participate. On output, this is the state of each of the domain's disk in relation to the backup operation.disk
- This sub-element describes the backup properties of a
specific disk, with the following attributes and child
elements:
name
- A mandatory attribute which must match
the
<target dev='name'/>
of one of the disk devices specified for the domain at the time of the checkpoint. backup
- Setting this attribute to
yes
(default) specifies that the disk should take part in the backup and usingno
excludes the disk from the backup. exportname
- Allows modification of the NBD export name for the given disk. By default equal to disk target. Valid only for pull mode backups.
exportbitmap
- Allows modification of the name of the bitmap describing dirty blocks for an incremental backup exported via NBD export name for the given disk. Valid only for pull mode backups.
type
- A mandatory attribute to describe the type of the
disk, except when
backup='no'
is used. Valid values includefile
,block
, ornetwork
. Similar to a disk declaration for a domain, the choice of type controls what additional sub-elements are needed to describe the destination (such asprotocol
for a network destination). target
- Valid only for push mode backups, this is the
primary sub-element that describes the file name of
the backup destination, similar to
the
source
sub-element of a domain disk. An optional sub-elementdriver
can also be used, with an attributetype
to specify a destination format different from qcow2. scratch
- Valid only for pull mode backups, this is the
primary sub-element that describes the file name of
the local scratch file to be used in facilitating the
backup, and is similar to the
source
sub-element of a domain disk. Currently onlyfile
andblock
scratch storage is supported. Thefile
scratch file is created and deleted by libvirt in the given location. Ablock
scratch device must exist prior to starting the backup and is formatted. The block device must have enough space for the corresponding disk data including format overhead. IfVIR_DOMAIN_BACKUP_BEGIN_REUSE_EXTERNAL
flag is used the file for a scratch offile
type must exist with the correct format and size to hold the copy and is used without modification. The file is not deleted after the backup but the contents of the file don't make sense outside of the backup. The same applies for the block device which must be formatted appropriately.
Examples ¶
Use virDomainBackupBegin()
to perform a full
backup using push mode. The example lets libvirt pick the
destination and format for 'vda', fully specifies that we want a
raw backup of 'vdb', and omits 'vdc' from the operation.
<domainbackup> <disks> <disk name='vda' backup='yes'/> <disk name='vdb' type='file'> <target file='/path/to/vdb.backup'/> <driver type='raw'/> </disk> <disk name='vdc' backup='no'/> </disks> </domainbackup>
If the previous full backup also passed a parameter describing
checkpoint XML that resulted
in a checkpoint named 1525889631
, we can make
another call to virDomainBackupBegin()
to perform
an incremental backup of just the data changed since that
checkpoint, this time using the following XML to start a pull
model export of the 'vda' and 'vdb' disks, where a third-party
NBD client connecting to '/path/to/server' completes the backup
(omitting 'vdc' from the explicit list has the same effect as
the backup='no' from the previous example):
<domainbackup mode="pull"> <incremental>1525889631</incremental> <server transport="unix" socket="/path/to/server"/> <disks> <disk name='vda' backup='yes' type='file'> <scratch file='/path/to/file1.scratch'/> </disk> </disks> </domainbackup>